How to program XBOX 360 Ms4r-X Rapid Fire Controller with
PC/Smartphone/Tablet
Suitable only if your controller include additional programing ISPB module.

ISPB module convert Ms4r-X-110 to Ms4r-X-3000.
1. Programing.
2. Create mode.
3. Load mode into controller.
4. Ready modes - Templates.
5. Your current created mode.
6. Input your previously created mode.
7. How to Program - Example.

1. Programing.

The table below (see Create mode) include 7 steps and every step include a few features. Mixing of different features of the 7 steps allow to create more then 3000 different combinations. In each step you can choose only one feature at one time. You can create your own mode or can choose one of the ready modes (see Ready modes - Templates) and then upload to your controller (see Load mode into controller) or customize as you need (see Create mode).

2. Create mode.

Right setting
RT Action: RT speed/time: RT Sub Action:
Step 1:
Step 2 - Tenth:
Step 2 - Ones:
Step 3:
Select RT action
Select RT Action first
Select RT Sub-Action

Left setting
LT Action: LT speed/time: LT Sub Action:
Step 4:
Step 5 - Tenth:
Step 5 - Ones:
Step 6:
Select LT Action
Select LT Action first
Select LT Sub-Action

Left and Right setting
Mimic Action:
Step 7:
Select Copy-Cancel action

3. Load mode into controller.

Your choice is: Select your choice



4. Ready modes - Templates.

Choose one of the modes below and then push Start to begin load your selected mode into controller.
+ Without Rapid Fire
+ Rapid Fire
+ Jitter
+ Burst2
+ Burst3
+ Burst4
+ Burst5
+ Dual
+ Akimbo
+ Auto Aim
+ Quick Scope

5. Your current created mode.

Create any combination and then save this code. Next time you can upload this code instead choose many options or you can send this code to your friend and he can upload the same created combination into his controller.

Your custom created code:


6. Input your previously created mode.

Upload your previously created code here.

Input Code:    


7. How to Program - Example.


Let's program Slot1 Mode 1 to Jitter YY + Drop Shot Manual - 25sps
1. To program your controller enable Ms4r-X (if not enabled).
2. Choose Slot1 and Mode1.
3. Push and hold Left Dpad + tap one time RT.
4. 4th LED and 3rd LED will flash simultaneously continuously.
5. Release Left Dpad.
6. Both 4th LED and 3rd LED will flash simultaneously once.
7. Then 4th LED and 3rd LED will flash to show current combination number loaded into Slot1 and Mode1.
8. After showing current combination loaded into current Slot and Mode 4th LED and 3rd LED again will flash simultaneously continuously.


9. Put your controller 1-5 inch near your PC/Smartphone/Tablet speaker.
10. Go to Ready modes - Templates and choose Jitter - 25. Jitter YY 20sps + Drop Shot Manual.
11. Then go to Create mode and change 'RT speed/time' to 25sps.
12. Go to Load mode into controller and push Start.
13. During programing you will hear different sounds. If programing OK and your controller accept the sounds then after each sound 4th LED and 3rd LED will toggle ON and OFF.
14. After successful programing 4th LED and 3rd LED again will flash simultaneously continuously.
Note: If both LED's 4th LED and 3rd LED not toggle ON and OFF during programing then put your controller close to PC/Smartphone/Tablet speaker or increase the volume. Then again go to Load mode into controller and push Start.
16. Choose any semiautomatic weapon and push RT to shoot with Jitter YY to test your setting.


17. Now you can save your mode if you like it or cancel it.
18. Turn OFF programing mode. Push and hold Left Dpad and tap one time RT (see Button combinations).
19. Both 4th LED and 3rd LED will flash continuously alternately until you make your choice to Save or Cancel your setting.
20. Release Left Dpad.
21. To Save your setting push and hold A button for about 2 seconds until 4th LED and 3rd LED will be OFF.
Or if you want Cancel your setting then push and hold B button for about 2 seconds until 4th LED and 3rd LED will be OFF.
22. Release A if you saved your setting or release B if you canceled your setting.
23. 4th LED will flash 1 time and 3rd LED will flash 1 time (Slot1 and Mode1).